Glasgow Daily Times, Glasgow, KY


January 2, 2014

KDFWR reports 27 cranes taken in local area

GLASGOW — Barren River Lake is still over winter pool, standing at 534.5 feet Wednesday morning. Crappie fishing continues to be pretty good. A couple of friends went last week and came back with a good string, including several over a pound, fishing jigs. There is no report this week on the bass action.


According to the Department of Fish and Wildlife, 27 sandhill cranes were taken in Barren County during the first two days of the season. They reported 33 had been taken statewide, well below the quota of 400 set this season which will continue through Jan. 12. The season opened Dec. 14 and most of the birds harvested in Barren were in the vicinity of Barren Lake, which hosts the biggest roost in the state.


Remember the Barren Bassmasters have set their 22nd annual swap meet for Jan. 18,  from 7:30 a.m. - 2 p.m. at the Cave City Convention Center. Tables are available for dealers ($1.50 per foot) and tables for the public are free.

For more information, you can call Glenn Reeves at (days) 270-646-7104 or (nights) 270-651-5348. Or, email him at


New KDFWR writer Kevin Kelly is the author of this week’s Kentucky Afield offering and it concerns caring for your hunting weapons:

The holidays are a good time to check one item off your to-do list: ensuring your rifle is clean and in tip-top shape for the next hunting season.

“If you want your rifle to last longer, the best way to do that is to keep it from getting rusty,” said Bill Balda, an expert marksman and the Hunter Education Supervisor for the Kentucky Department of Fish and Wildlife Resources. “The best way to keep it from getting rusty is to clean and lubricate it. As a result, you get to know your rifle better and you know it’s in safe working condition.”

“The simplest way to unload a muzzleloader is to fire it into a safe backstop. But the residue from burnt black powder and even its substitutes is extremely corrosive,” said Mark Marraccini, Kentucky Fish and Wildlife spokesman and a muzzleloader craftsman. “If you leave that inside the barrel for very long it would be just like dipping any piece of steel into corrosive acid or salt. It’s going to start etching its way into the steel immediately.”

Marraccini warns against creating pits in the barrel. “They will affect accuracy later and could make your muzzleloader unsafe,” he said.

Before undertaking any cleaning routine, first make sure the rifle is not loaded.

For centerfire rifles, Balda suggests cleaning the barrel with patches wet with gun cleaner first, then, a wet brush for five to 10 passes. After the initial cleaning, continue to use dry patches until they come out clean. A light coat of oil then can be applied in the bore.

“If you want to remove copper buildup after shooting 500 to 1,000 rounds, there are chemical cleaners that can be used. I use a bore paste, which is like a jeweler’s paste. It has grit in it that is harder than copper but not hard enough to score the steel of the barrel,” Balda said. “Most liquid cleaners have ammonia in them. When you run that patch through and take it out and it has blue on it that means you have copper in the barrel. I would first brush it out and then go ahead and patch it dry. Then, put bore paste on another patch and scrub it in there.”

Balda recommends placing a piece of wood on the end of the barrel to prevent the cleaning rod from coming out.

“When you pull that out, that paste is going to look black no matter what,” he said. “Then check it with a wet patch. If the wet patch is blue, there still is copper present. Then, you have to keep doing it.”

While you’re at it, check the bedding screws. Wood stocks tend to shrink and swell with changing environmental conditions and that can loosen those screws.

If your rifle is a bolt action, Balda suggests removing the bolt and cleaning the bolt face and the receiver inside the action with a toothbrush-style cleaning brush. Then, wipe with a light coat of oil. Wipe down the outside of the rifle and clean the lenses on the scope.

For muzzleloaders, hot soapy water effectively cuts through black powder residue and the heat from the water helps dry remaining moisture inside of the barrel after running a dry patch through it, Marraccini explained. If you can remove the barrel, set the base of it in the water and work the cleaning rod similar to a plunger.

“When you can run a dry patch down it and it comes out entirely clean, then I like to put some natural greases on; Bore Butter is one brand of it. There are other brands out there, too,” Marraccini said. “You put it on a patch and run it down there until you’re satisfied that you’ve got a coating on the inside of the barrel.”

Treat the exterior of a muzzleloader the same as you would any rifle: wipe it dry and remove any fingerprints.

With flintlock muzzleloaders, he advises cleaning the area around the lock. On a percussion cap muzzleloader, a nipple pick and a nipple wrench help clean hard-to-reach areas.



Text Only
Daily Times sports photo

Barren County vs. Glasgow Challenge Cup boys golf